Jump to content

Thailand Hotels | Bangkok Hotels | Phuket Hotels | Pattaya Hotels | Chiang Mai Hotels | Hua Hin Hotels
* * * * * 1 votes

Tips: Running Off

No replies to this topic

#1 WildOne


    Advanced Member

  • Root Admin
  • PipPipPip
  • 370 posts
  • Gender:Male

Posted 24 October 2014 - 11:01 AM

Running Off

If something goes wrong on the foredeck, the natural instinct for many sailors is to luff up head-to-wind until the situation can be resolved. The problem with this course of action is that on most displacement boats it does no one on board any favors, putting a strain on the forestay when everything starts shaking, and increasing the apparent wind.

As long as you have sea room to leeward, it is a far better course of action to run off instead. Doing so shelters the headsail in the wind shadow of the mainsail. This in turn will collapse the headsail and leave it hanging. There’s no mind-jarring clattering about the deck because the apparent wind will magically drop as well. Getting the boat into this position makes dealing with a fouled headsail furler, subduing a cruising chute that has gone berserk or fixing anything else that might be shaking around much less stressful than trying to do the same thing while plunging directly into the wind and oncoming seas.


Sail Saver 

If you have older Dacron sails, a good method of preserving them while improving their working ability is to treat them with a fabric spray (the type used for tents, shoes, or furniture). Most likely you will see a difference right away. During rainy weather the sails will shed water better, keeping them lighter and better shaped, and that can really make a difference in your boat’s heavy-weather performance. The fabric treatment also makes the sailcloth more pliable and easier to flake and fold. Several of my friends now regularly treat their sails and have commented that it is inexpensive for a couple of spray cans, and it is the most cost-effective performance enhancement they can lavish on their boats


A Cutter that Cuts It

For many cruisers, a cutter rig is the one that works best—so long as the staysail is cut for windward work, fairly flat with its draft well forward. A staysail also needs a good sheet lead. Sheet tracks and leads for many staysails seem to be placed more for convenience than effectiveness and often fail to take into account the staysail’s dual role.

On most cutters, the staysail is used with a larger headsail primarily when close reaching. When sheeted inside another headsail, the staysail must be trimmed more tightly than its companion, requiring a track fairly well inboard. However, when used by itself as a heavy-weather windward sail, a staysail may require a more open sheet lead, especially as few cruising boats are capable of pointing really high. At these times it is better for the track to be farther outboard.

The problem with staysails is that most are so small they are close to storm-jib size. If the inner forestay is attached to the mast at the upper spreaders, the sail may also have a short luff, and it is the luff of the sail that powers a boat to weather. For this reason, many cruisers have adopted what some call a Solent stay, which is attached to the mast and deck only a couple of feet behind the headstay. This allows for a staysail of sufficient size to power the boat upwind and in most cases does not require the running backstays used with most other cutter rigs. The downside is that you do have to change sails if you actually need a storm jib.

Karate Corner

Good communication between people on the bow and helm is very important when coming into a crowded anchorage or harbor. I used a system of hand signals for many years, and communications had been pretty successful other than the occasional confusing moment—for example, are your fingers pointing because that’s the direction to steer or because there is something in the water?

Then one day we watched a speedboat race on a TV sports channel. It wasn’t the standard dash around buoys, but a time trial in a narrow figure-eight channel that ran through a swamp. The boats were so fast that the driver could react quickly enough only if he followed hand signals given by the navigator next to him.

The navigator held his hand out ahead of him as though he were ready to make a karate chop on a board. When a course correction was needed, he would point his arm in the direction he wanted the driver to steer and then make a rapid chopping motion with his hand. We tried this on our next cruise to the North Channel of Lake Huron, and it worked very well. We use the chopping motion to indicate what direction to steer and simply point, without chopping, to indicate a hazard ahead. A clenched fist followed by a pointing finger indicates a rock or obstruction. When we’re pulling up the anchor, an arm pointed in a specific direction shows the general direction of the rode and anchor. A fore-and-aft chopping motion signals that the anchor is under the boat and it’s time to put the engine in reverse. Once your team knows the routine, you can start chopping and stop shouting.

Light line only

Many years ago an acquaintance was nearly strangled when his knife, which he wore on a strong lanyard around his neck, got tangled up in the anchor chain as he was easing a 45-pound hook over the bow roller. It could have ended badly had he been alone. It's certainly a good idea to attach lanyards to valuable items like flashlights, knives, shackle keys, and so on so that you don't lose them overboard, but make sure the line is weak enough so it will snap easily if whatever it's attached to gets caught up in a flailing sheet or anchor rode. One way to do this is to connect the implement to the lanyard with a plastic clip. Better to lose a knife than a hand or a life.

Will we collide?

To evaluate the risk of a collision, check whether the vessel in question is maintaining a steady bearing relative to you. Initially, you can do this by keeping your head still and seeing whether the other vessel remains in place over a particular stanchion, shroud, or other likely reference. If you’re not sure if the vessel is moving, take a bearing with a compass and keep checking as the range closes. You might even use the electronic bearing line on your radar. In confined waters, it is easier to tell whether the other craft appears stationary relative to its background. While difficult to prove mathematically, this old rule of thumb works every time unless the other craft is almost on the beach. If the other vessel stays in front of the same distant field or headland as you approach, you are on a collision heading, so watch out.

Passive radar reflector

Wooden boats with wooden masts make poor radar targets; the same is true of fiberglass hulls with carbon-fiber masts. Even boats with aluminum spars are notoriously unreliable targets, which is why all sailboats should carry passive radar reflectors. Yet few boats have these permanently mounted. Instead, most rely on corner reflectors to reflect a radar signal directly back to the scanner that transmitted it. These work well on many navigation buoys, but size is important: a 12-inch corner reflector is theoretically less than 1 percent as effective as a 36-inch reflector.

How to be seen

We all hope the lookouts on those huge container ships will see our little sailboats in rain, mist, and low light. Should we find ourselves in trouble, we pray that our rescuers will be able to make us out in the breaking waves.

Some sailors have long recognized the value of being highly visible. Many ocean-racing boats have brightly colored hulls and decks. In New Zealand, sailors are strongly advised to sew bright orange stripes on their sails. Yet most cruising sailors own boats with white sails, white or blue hulls, and gray or white masts and so are difficult to see at sea.

It is very easy and inexpensive to dramatically improve your boat's visibility. Whether you're bluewater cruising or just daysailing around the coast or lakes, it's worth the effort. Painting the top few feet of your mast international orange will make the boat much more visible from a distance without affecting its aesthetics. I painted the top 4 feet of Hawk's masthead. It’s very visible in profile, but from the front and back, the mast section is much narrower and a 6-foot stripe would be better.

Fender Boards

When you go alongside a high dock or wall, you need to protect your fenders. This means having fender boards that are rugged enough to do the job and not just look nice. Always carry two fender boards, and if there is space I carry three. There is no need to make theses fancy; mine are 6-foot-long 2x6-inch planks. I’ve drilled two 1/2 –inch holes through the full width of the boards at each end. To hold the boards in place in front of the fenders I run tie lines through the drilled holes and then use figure-eight knots to secure the lines on the underside of the fender board.

Trip Lines

If you ever had your anchor catch under a rock or other obstruction, you’ll be glad you rigged a trip line. But if you ever have someone else’s anchor buoy and trip line wound around your propeller, you’ll curse trip lines and all who use them. In crowded anchorages, trip lines often cause more problems than they solve. It is not unheard of for a boat to swing over its own or someone else’s anchor buoy, getting the line caught around the rudder or propeller and tripping the anchor unintentionally.   If you absolutely must use a trip line, make it a long one; secure it to the anchor rode at intervals with a light, easy-to-snap string, and make it fast to one of the bow cleats. That way, the worst that can happen is that the trip line may get twisted around the anchor rode as the boat swings to a reversing current or wind shift. You may have a bit of fun sorting out the tangle when it’s time to leave, but that’s nothing compared to the joy of having your trip line wound around your own prop.

Beware of Buoys

“Just head for the buoy up ahead and make sure you leave it to the starboard.” An instruction like that is asking for trouble, especially if a novice is steering. All it takes is a bit of cross current and the boat will be gradually set off course, all the while pointing faithfully at the buoy; it may even be set onto the very hazard the buoy is marking. When you steer toward a buoy always note the compass heading and be ready to compensate for a cross current if the compass heading changes.

A “Burned” Impeller

Impellers for the engine’s raw-water pump don’t last forever. Even if they aren’t destroyed by having been run dry following a blockage in the raw-water line, they still deteriorate over the years. If you’ve never had to change one, try installing a new one when the boat is safe on it’s mooring, and then go out and buy a new spare. You might be surprised by what you discover.

• Some raw-water pumps require a fresh gasket each time the impeller is changed. Do you have a gasket on hand?

• Does your screwdriver fit the machine screws that attach the cover plate?

• Might you lose a screw in the bilge? It’s so easy to do. If so, can you reach it or should you carry a couple of spares?

• All this is vital knowledge when you have to do the job heeled over in rough seas on a dark night.

Ladder Line

A walk down any dock reveals numerous ways to secure boarding ladders. Most of them are improvised from bits of string, Velcro, and elastic straps, and many exhibit the use of knots that can be hard to untie in an emergency. A SAIL reader has come up with a safer way. He mounted a clamcleat on the stanchion and tied a short length of line around the handrail directly above it. He loops the line around the last rung of the ladder in the raised position and secures the free end in the cleat. The beauty of this simple solution is that the ladder can be dropped in a jiffy with a simple flick of the wrist.

The Towing Bridle

Some boats can’t tow directly from a cleat because of its self-steering. Other boats have difficulties with backstays. The answer is to rig a simple towing bridle. Even when the stern is unencumbered, using a bridle has the advantage of spreading the load between at least two points. Make it up so that one end can always be slipped when necessary, then secure the tow rope to the bridle with a bowline. The towed boat cleats it off so that the line can be released in an emergency. Take the strain gradually, and don’t let any dangling rope be sucked into your own propeller.


Snapshackles are suppose to stay closed, but unless they are specifically designed to lock shut, they can open unexpectedly. If you aren’t sure whether your snapshackle will stay closed—after all, the sudden opening of a spinmaker-haylard snapshackle can be very exciting—tape the shackle shut with electrical tape. When you want to open the shackle, cut the tape with a knife.

Ready to Run

Where do you keep your kedge anchor and rode? Ten to one it’s all tanged up in the middle of the cockpit locker, and it will take at least ten minutes of fiddling and cursing to get it ready to deploy. If you’re sailing in waters where you might need to set a second anchor in a hurry, you should consider emulating this cruiser and keep a spool of strong webbing rigged on your stern pulpit. It can serve as a towline, a long mooring warp, or a kedge rode—just shackle on the anchor and a short length of chain. When you’re done with it, wind it back on its spool.

Fresh Water

Design a shade awning so that it is also efficient collecting rainwater. First shape the awning with a belly on each side where water can collect; a rope running along each side of the awning forms a gutter. A shallow funnel is sewn into the lowest part of each belly, and 1-inch plastic fittings provide the attachment points for drain hoses. The system is designed to handle the large volumes of water often produced by short, but very wet tropical rainsqualls. Small-reinforced canvas loops are sewn in place near the hose fittings and along the gutter. These serve as attachment points for tie-down lines and limit the amount of flapping.

The drain hoses slide into the inside of the tapered hose to ensure a tight fit, and both hoses are long enough to reach the water-tanks fills on either side of the boat. The long hoses allow the rainwater to route into one or both tanks.

Cleat Surrogate

If you think you need to tie up to a short pontoon, you’ll have to rethink your usual arrangement of dock lines. You’ll have to lead the stern line forward—which is far from ideal—and take a short spring line from a midships cleat to the same dock cleat as the stern line. Use two bow lines, if possible, to keep yawning to a minimum. If your boat doesn’t have a midship cleat, resist the temptation to tie the spring to a stanchion or shroud except as a very temporary measure (and never let a boatbuilder see you tie a dockline to a stanchion).  If you can, fasten a block or shackle to the toerail and make the springline fast to that.

Reef Untangler

We love our slab-reefing setup but constantly had problems with the reefing getting tangled up around the end of the boom. The solution was simple. We always carry a couple of spare battens inside the boom, and we discovered that leaving one poking out prevents this from happening.

Lasso the Buoy

In the course of our circumnavigation we’ve often encountered mooring buoys that don’t have pick up lines. We sail doublehanded, so these can be problematic, especially if it’s windy. Here’s how we deal with them. One of us stands near the bow with a long line that is lead outside the lifelines with one end secured to a bow cleat. We coil the line and divide the coil between both hands, with a bight of line hanging free between the hands. As the helmsman steers the boat slowly alongside the mooring buoy, the other throws the line neatly over it, effectively lassoing it with the bight. Keep hold of the unsecured end of the line, harden up on the line as much as possible, and then cleat it off. The boat will settle to the buoy, and you can rig another line through the eye on it at your leisure. You can always use this trick to snag a cleat when coming alongside a dock—for instance, if the wind is blowing the boat away from the dock and you don’t want to make a risky jump ashore.

River Anchorage

When anchoring in a river, take note of the prevailing and forecast wind directions. Will the wind at any time oppose the current? If it does, the boat will not lie well to its anchor. It might even sail around enough to pluck the hook out of the bottom. If at all possible, choose a section of the river where the prevailing wind is blowing across the current. The boat will tend to lie with its bow into the current and you’ll sleep more soundly.


Improve Off-wind Performance

If the wind comes forward of abeam, the genoa sheets’ lead will now be too far outboard. Ease the barber-hauler line and take up on the genoa sheet. This will pull the clew in to somewhere between the inboard and outboard positions, wherever the sail works best.

If the boat has a reaching strut, you can set it up on the leeward side of the mast and sheet the genoa through the jaw at the outboard end of the pole. This will get the jib clew farther outboard than the barber-hauler will, opening up the slot even more. Another alternative is to sheet the genoa to the end of the main boom. However you do it, getting the headsail’s sheet lead outboard will improve your off-wind performance.


How to Throw a Rope

You should be prepared to make contact with a MOB without special equipment: this means throwing a line as effectively as possible. Quickly form four or five small loops in your throwing hand. Then make four or five loops in your other hand; arrange the loops in the order on which they will leave your hand when the line is thrown. Throw the small bundle of loops first. They will pull the second group of loops from your stationary hand. A sideways throw can work well and improve accuracy.

Ease the Main

When maneuvering under mailsail alone, don’t expect your boat to sail properly upwind with the sheet trimmed in hard. You do this when flying a genoa to avoid backwinding the main, but without a headsail the main is cutting clean air. Close-hauled under main alone, it’s best to steer about 45 degrees of the true wind, then trim the main to the breeze as though you were reaching. The boat will end up pointing higher and sailing faster. It won’t be going sideways, either.


Headfoil Damper

Roller-furling extrusions tend to pump in high winds when the weight of the sail has been removed. Here is a wonderfully simple way to correct this problem. Make or buy a 2-foot length of luff tape with grommets on either end. With the genoa halyard at the top grommet and a line running from the bottom grommet to the base of the mast, insert the luff tape into the extrusion slot and raise it halfway up the headstay. Tension both lines as necessary. The first time we prepared for a hurricane we had to improvise a damper by tying a bowline in one end of a piece of line and clipping the halyard to it. We wrapped the line around the forestay once, and then twice more about 2 feet farther down. We raised the line about halfway up the headstay and then secured the halyard and the line. Our rig has never been as quiet as it was during that hurricane.


Wax your Bottom

We sail in the Pacific Northwest and use our inflatable dinghy year round. We had a real problem with marine growth on the dinghy’s bottom until we tried waxing it. We’ve found that waxing the bottom lets us keep the dinghy in the water for up to four weeks without problems. Then all we need to do is lift it out, wash it clean, and, after it dries, re-wax the bottom. I prefer to wax the bottom of my inflatable, in case I need to patch it, rather than paint it with anti-fouling. For longer-term wet storage, though, you might have to consider painting the bottom.

Beat the Blind Spots

I once saw a one-design racing sailboat sail directly into an anchored motorboat. The racer’s deck-sweeping genoa obscured the crew’s view of the powerboat until it was to late to avoid it. I’ve come close to taking out navigational marks for the same reason— they were hidden in the big blind spot created by my genoa. The solution to the problem is plain. If you’re on a racing boat, detail one of the crew to be the lookout. If you’re on a cruising boat, use a higher-clewed sail. There is another blind- spot to the windward when you’re close-hauled and steering from the leeward rail. Don’t forget to stick your head up every few minutes and have a look around.

Avoid Damage Aloft

One potential danger when sailboats lie alongside one another for a convivial night is that if they roll to a wash or begin to move in an unexpected sea, the spreaders can clash together and suffer catastrophic damage. Always look aloft when rafting up and make sure the masts are well out of line. Rafting bow to stern is a good way to prevent spars from clashing.


Who has the Right of Way?

A useful aide-memoire for crossing another vessel in daylight when both boats are under power–in a harbor, for example–is to ask yourself which sidelight you would be seeing if it were dark. If the answer is a red, or port, running light, you must take care and stay our of the other boat’s way. A green light would indicate that you are clear to go. So if you would see a green, or starboard, running light, you can continue carefully on your present course.


Chain Collar

If your anchor is hooked on an underwater cable or snagged under a rock, you may be able to free it with a chain collar. Loop a piece of chain about 12 inches long around the anchor rode and join the ends with a shackle. Harden up on the anchor cable until it's vertical and then slide the chain collar down it on a length of line. The aim is to get it over the shank of the anchor and down near the crown. If you ease off the anchor cable and heave up and down on the collar line, you may be able to pull the anchor clear of the obstruction. If it proves stubborn, try pulling on the retrieval line from the dinghy as the boat settles back on the rode; the change in angle maybe all that's needed to coax the anchor free.


Letting go the Sheet

Releasing a loaded-up sheet from a winch when a boat tacks can be just cause for nervousness. Sailors who have just moved up to big keelboats often underestimate the loads on a sheet. On a boat up to 40 feet or so, the safest way is to first ease off a few inches, keeping the flat of one hand pressed against the turns as they surge round the winch drum. Now take off a turn or two, always leaving a couple on the drum for safety, and wait for the sail to begin to lift at the luff. As soon as this happens, pull the turns positively upward off the drum, keeping your grip directly above the axis of the winch. The turns will whip off cleanly, they will never foul, and your hands will be safe.


Marking Chain

There are a number of ways to mark your anchor chain, including using paint or plastic-wire ties. I prefer to use strips of nylon spinnaker cloth.

First lay out the entire chain on the dock and flake it in even lengths. Choose a length that is appropriate to the depth of the waters you’ll be cruising in. I use 25-foot lengths. Then tie one of those easy to see pieces of cloth through the links that start each end of the designated length. I wrap the nylon strip through the link twice and tie it with an overhand knot.

We bought spinnaker-cloth tapes from our sailmaker in 2-inch wide rolls, in red, green and white. We cut the tapes into 30-inch lengths and marked each with a felt-tip marker to indicate the number of feet of chain that have been put out.

The colors let the foredeck crew know how much chain is going out even though they can’t see the actual numbers. I’ve tied green tapes on all the 25-foot marks (25, 75, 125, 175), red tapes on the 50-foot marks (50, 150, 250), and white tapes on the 100-foot marks (100, 200).

The colors are easy to see, the nylon cloth goes through the windlass easily, and the cloth last longer than paint.


Cut the Cheese

A line end that’s neatly done up into a Flemish coil, or “cheese,” looks very salty, especially on the gleaming cabintop of a classic boat, but it’s not a good way to treat a line that might have to be free in a hurry. Cheese lines are prone to kinking and need to be thoroughly shaken out before you get underway, or there’s a good chance they’ll snarl up just when you least want them to. Cheese lines are also great dirt traps, as you’ll find out if you’ve left one on your cabintop for a few days.


Stanchion Safety

When 200 pounds of force is applied to the top of a 30-inch stanchion, as much as 3 tons of pull can be exerted on the stanchion’s base. That is more than enough to rip poorly mounted bolts up through the deck. Make sure all stanchion bases have oversized metal backing plates (not just shoulder washers), and check all the bases periodically for distortion. If the base socket holds the stanchions in place with set screws, replace them with bolts that pass through the stanchion wall.

When a lifeline fails, the cause is usually corrosion. Although coated wire is popular for lifelines, the plastic that covers the wire can hide the corrosion. That is why 1 X 19 stainless-steel rigging wire is superior. If you’re still using coated wire, examine it carefully for the telltale brown stains that cast doubt on its reliability. Gate hardware is also susceptible to failure. If you eliminate it, your lifelines will be strengthened; the downside is that it might be harder to get onboard.

Lifelines must never become slack. If the turnbuckles have lock nuts, secure them with Loctite and replace the copper pins. Spread open the ends of the pins and then cover them with tape.


Sail Saver

If you have older Dacron sails, a good method of preserving them while improving their working ability is to treat them with a fabric spray (the type used for tents, shoes or furniture). Most likely you will see a difference right away. During rainy weather the sails will shed water better, keeping them lighter and better shaped, and that can really make a difference in your boat’s heavy-weather performance. The fabric treatment also makes the sailcloth more pliable and easier to flake and fold. It’s a cost-effective performance enhancement to lavish on your boat.
Signal Advantage
If you have an on-the-water emergency during the day, keep in mind that a mirror is a very effective signaling device. If the weather is clear and there is sunlight, the reflection from a mirror can be seen up to 100 miles away. While it does need sun, a mirror doesn’t depend on batteries, satellites, or the electronic watchkeeping of a potential rescuer. Reflecting sunlight into the eyes of a person on another boat or plane should get their attention. You could heliograph an SOS code, but simply keeping the beam on your target should quickly lead the person on the other end to conclude that the flash he is seeing is not a chance occurrence.
Specialized signal mirrors come with aiming devices, but any handheld mirror will work if you do the following: Hold two fingers in a “V” at arms length with your target inside it. Now hold the mirror against your cheek just below eye level and adjust the mirror angle so the reflected sunlight shines over your fingers. Turn the mirror so the sunlight plays back and forth across your fingers, and it will also move across the target inside the “V”. Keep at least two signaling mirrors on board. Put one in your ditch bag and the other on shelf near the companionway.
Anchoring: a Shorter Scope

It is well known that three times the depth of the water is a good starting point for determining the scope you need when anchoring with a chain. This rule is not cast in stone, however, and you might safely opt for less scope if space is tight, so long as your anchor seems well set, conditions are not extreme, and you will be aboard at high water. This can be particularly useful when swinging room is tight and the tide is due to fall during the night, because you know that your scope will increase for some hours before it begins to decrease once more. If your anchor is holding at bedtime, it should hang on until morning light.

To Flash or Not

Flashing white lights are far more noticeable than fixed ones and can be much brighter for the same average power drain. However, it’s dangerous and illegal to show anything that can be confused with a navigational aid, so flashing lights of any color mustn’t be used anywhere in coastal waters. The situation on the high seas, where there are no navigational aids, is not well defined. The International Rules state that the use of flashing lights for drawing attention to a vessel should be “avoided.” But if a vessel also carries the required lights, and if the flashing light does not interfere with them being seen or with the watchkeeper’s vision, their use isn’t actually prohibited. Unofficially, slow-flashing white strobes are used for various eye-catching purposes– on scientific and fishing drift buoys, for example. Masthead strobes are more likely to be noticed than ordinary navigational lights, and at a much greater range, so it’s understandable that singlehanders sometimes use them on the high seas, in addition to the regulation lights.

Quick Anchor Ranges

To make a quick check whether you got a good bite after dropping the hook, look for a simple range—say a piling on a dock and a tree on shore, or a flag pole and a nav aid—that is roughly parallel to the wind or current. It will be readily apparent if your boat is still on the move, long before it might otherwise become apparent on a chart plotter. Assuming your anchor does hold, you can also this as one of your three ranges after taking a fix before settling down for good.  

Rig Your Galley for Heavy Weather

If you're on passage and expecting a blow, it not enough to secure things on deck and shorten sail. You need to also prepare your galley. Specifically, set aside a few meals that will be both nourishing and easy to consume, so that you won't have to go digging around in cupboards or the bottom of the fridge when the boat is thrashing about so that it feels like you're inside a washing machine. In terms of menu, think dog bowl food--pre-made items that can be easily reheated (nothing beats a nice hot meal when you're cold and wet!) and then eaten out of a single dish with a spoon.


Push Yourself a Little

All to many sailors fire up the auxiliary and head back to short as soon as the wind either dies or comes on stronger than they’re accustomed to—which is too bad. There’s nothing like battling through a calm or a bit of a blow for bolstering both your skills and your confidence. With that in mind, think about how your and boat would respond in more extreme conditions, give your boat a good going over to make sure it’s ready for a little more wind, in particular. And then the next time things get a little challenging, let things hand out a little. You might be surprised at how much fun you have.


Wash away a sticky track

Having trouble with a sticky mainsail luff track, but don’t have any fancy space-age lubricants to help the sail along its way. No worries, try a few drops of dish-washing liquid, applied the length of the groove, or along the sides of the slugs or under the cars. It will, of course, was off eventually. But as a short-term fix, it can’t be beat.


Reef Your Jib Leads

As you roll in some of a roller-furling jib to keep your boat on its feet during a blow, don't forget to move the jib-lead car as well; otherwise, the increasingly horizontal force that it imparts on the sail will allow the upper part of the leech to curve, or "twist," excessively off to leeward. Moving the lead forward will allow the sheet to continue pulling down on the sail as well as aft, controlling the amount of twist so that it will continue to parallel the amount of  twist in the main and thereby provide maximum power and efficiency. 


Boxing the Winch

To ensure you don't lose any of those tiny bits and pieces when servicing a winch, cut out a hole from the bottom of an appropriately sized box and  then slip said box over the winch, securing it snugly around the base before disassembly. This is a good idea not just if your boat is in the water, but on the hard as well. It's amazing how cleverly a pawl or some other tiny but oh-so-vital part can get itself lost among the general detritus of a typical boatyard. 


Dead Downwind is Slow

Racing sailors rarely if ever sail dead downwind, and neither should you, especially in light air. Not only will hardening up onto a broad reach and then zig-zagging downwind get you to your destination faster, the sailing itself will be more enjoyable as you harness the power of apparent wind to increase your speed through the water. Don't worry about "maximizing VMGs" or anything overly technical like that. Just harden up until the boat accelerates enough to create a pleasantly gurgling bow wave. Then as the angle to your ultimate destination approaches what you believe will your gybing angle on the opposite tack (or as you run out of sea room!) put the helm down. As you are doing so, don't forget to take a look back at the other boats that sailed a straight-line course and are now well astern gazing longingly at your transom!


Let Your Sails Breathe!

In light air, all too many sailors over trim their sails in an effort to eke out that last bit of power, a mistake that is  exacerbated by the fact that taught sheets can create the illusion of lift. The correct approach, however, is to ease your sails out a bit to ensure there is nice, smooth, laminar flow over both the windward and leeward surfaces. Otherwise,  the air flow will detach from the leeward side, causing speed-robbing turbulence. When in doubt, let 'em out! Your sails need to breathe!


Shroud Telltales

There’s nothing like a few inches of yarn tied or taped to each shroud, say, seven feet above the deck, for keeping the person at the wheel in touch with what the wind is up to. In this day of electronic gadgets, it seems more and more sailors are forgoing installing these kinds of tried and true telltales, relying instead on their instruments to show them their apparent wind angles. But remember, sailing is about far more than just numbers. It’s about integrating a variety of different sensory input, and when it comes to apparent wind angle, there’s nothing like seeing the actual wind direction relative to your rig to give you an idea of how you and your boat are doing.


What Lies Beneath

When maneuvering under power or sailing at slow speed, don't forget that the current can be just as important as your heading and the wind direction. When aiming for a mooring, threading your way through a patch of fishing buoys or conning a well-marked channel, be sure to check to see if any of these fixed objects is leaving a "wake"—a sure sign the water in which they are sitting is on the move. If so, be aware that going "upstream" of this point may be a course fraught with hazard. Also, be sure to have an escape route in mind in the event you find at the last minute that clearing it won't be possible.

A Preventative Reef

There's an old adage that says as soon as you start thinking about possibly reefing, it's time to reef. But why wait even that long, especially when sailing with newbies? If things are looking at all puffy, why not throw in a reef at the same time you're hoisting your main, as opposed to waiting until that first knockdown? Doing so is simplicity itself, and if those possible puffs never materialize, shaking it back out again will be just as easy. Remember, there's absolutely nothing wrong with starting slow. Although the sounds or slatting Dacron and water rushing by may be music to your ears, they can be downright terrifying to someone who has never been sailing before. A preventative reef early on could very well mean the difference between your guests never, evergoing out with you again or becoming a regular part of the crew. 


The Second Time’s a Charm when Docking

There’s no law that says you have to make a dock on your first try, so if things start to look dicey, don’t hesitate to bail out and get yourself all lined up again and then start afresh. Marinas can be funny places, with odd wind shifts and quirky currents, thanks to the presence of the nearby shoreline and surrounding obstructions. Using the insights you've gained on your initial attempt can be especially helpful when conning your way into a new slip or dock for the first time. Whatever you do, don’t take a “damn the torpedoes” approach and try to jam yourself in no matter what. Although there’s no shame in a do-over, there will inevitably be plenty of shame to go around in the event things should go truly haywire!


Help out your Trimmers

Grinding in a big, overlapping headsail can be a real, well, grind—especially when short-tacking up a channel in heavy air. To help out your trimmers as they are getting in those last few inches of genoa sheet after coming around onto a new tack, try feathering up a few degrees to take some of the pressure off. Don’t alter course so much that you go back into irons or lose your headway completely. Just point the bow up enough to put a little backwind in the jib. Your crew will thank you for it, and you won’t has to listen to a bunch of mutinous grumbling next time you make the call of “ready about!”


A Hatch Headache Preventer

The sliding Plexiglas hatches over the companionways on some boats can truly be the bane of a sailor’s existence. Who among us hasn’t banged their head rushing topside without checking first to make sure the way was clear? To give you and your guests fair warning that they need to slide a hatch out of the way before going out into the cockpit, try tying a short length of line with a stopper knot in the end of it to the latch fitting at the end. That way, even if you have a cap on obstructing your vision upward, there will be an indicator right in front of your face as you start making your way up the companionway steps, warning you to beware. 


Your Fellow Wind Indicators

When it comes to reading the wind close inshore, there are typically any number of indicators to choose from, including flags, smokestacks and waving tree limbs. Farther out, though, one of the best ways of seeing what the breeze is up to is to use the old racing trick of watching your “competitors.” Are the sails on the boats in a bight of land a quarter mile away all hanging limp? Probably best not to go there if you have any interest in going anywhere fast. Similarly, if you’re just drifting, but the boats to windward a half-mile off have started healing dramatically and are clearly sailing on their ear, better be alert and maybe even think about putting in a reef. 



Heaving-to in bad weather offshore is something we all read about, but many of us will never do. Since it is such an easy maneuver it seems foolish not to practice in good conditions when nothing will get broken. Simply tack without releasing the jib, and keep the mainsail sheeted. Then put the tiller back over (as if to tack back again) and find the sweet spot that enables the boat to just forereach (crab to windward) with the jib backed. If the wind is up, reefing the main before the maneuver, or easing it slightly, might help. Heaving-to can be a restful point of sail offshore, useful when meals are served, some maintenance issue needs to be resolved, or you just need a rest. Practice makes perfect and knowing how your boat will behave in different situations is always beneficial.


Make it a double

Paint and varnish WILL spill at some point. A large plastic coffee can (empty of course) makes a perfect “holder” for the can or plastic container that is filled with paint. The double can contains any drips, is less prone to tipping over, and also provides a handy place to set down your brush. Plus, if you need to do so, a couple of holes poked in each side of the larger can and a string or coat hanger will allow for hanging off a ladder or rail. Purists might want to find a couple of them and use one for varnish and one for paint, but that is getting picky.


Blade prep

If you don’t carry a knife at all times, you are probably not alone. But you should have one handy in areas where something bad might happen. Stash one securely in the cockpit (somewhere it won’t affect the compass). And tape a sheath knife to the mast or the vang in an unobtrusive place, ready for action. The precious few seconds you save from searching for a blade may make a big difference in the outcome of a crisis.


Get your head out of the boat

We all have our own way of navigating, and no single way is always the best (despite some arguments). With today’s proliferation of electronic gizmos, handheld devices, displays, and autopilots, sometimes it is easy to forget that one’s eyes (and brain) are the best tools on board. And, using multiple sources of data, even from your eyes, is better than just relying on the screen to do the navigating. So, as often as possible, take a survey of the water, mentally checking off the landmarks and navigation aids, and then compare with the chart to see if it all makes sense. A quick look at the depth sounder completes the process. A paper chart is much easier for this purpose than a display screen, as you get a much fuller context of your sailing area. Plus, you can easily check ranges (two buoys or land objects lining up) and see what is coming up on your path without having to zoom out.


Tender Towing

So your engine has failed and there’s not enough wind to sail. Your mooring is in sight, there’s no immediate danger, and you would rather not call for assistance. What now? The solution could be right behind you, if you’re towing your dinghy. Even a 2hp outboard can get a 10,000lb sailboat moving at 2 to 3 knots in flat water. Secure the dinghy alongside the boat’s aft quarter; you’ll need to rig bow, stern and spring lines, and find places on the dinghy to make these fast. Gradually give the outboard more throttle to get the boat moving; once it has some way on, it is quite easy to maintain it. Leave the mainsail up so you’ll be ready in case the wind comes up. You’ll need to judge your approach to the mooring carefully, because it’s hard to slow down by reversing the outboard. 


Oil's Well

On smaller boats—and on some bigger ones—changing the oil and filter can be a nightmare scenario. Sailboat engines are typically shoehorned into their bays and access to service points is seldom as good as it should be. I’ve found the best way to change oil is to run the engine till it’s warmed up, then use a hand-operated vacuum pump with its pickup tube inserted into the dipstick hole. You can get these from any marine store. Changing the filter can be a chore too, depending on how hard it is to reach. Even if you’ve just hand-tightened the filter as recommended, it can be devilishly difficult to loosen it, and often you can’t get a decent grip with a filter wrench. In that case, a large hose clamp tightened around the filter barrel will give the wrench something to bite on. Do not ever succumb to frustration and stick a screwdriver into the filter and attempt to use it as a lever—it won’t work, and you’ll make a hell of mess. Don ‘t ask how I know this. Which leads to another tip—a disposable diaper spread out beneath the filter makes a great oil catcher.


Cleaning au Naturel

Forget expensive and toxic cleaning products. If you have a jug of white vinegar and a box of baking soda on board, you’re covered for most scenarios. A paste of baking power and water will get rust off stainless steel and mildew off fiberglass and other non-porous surfaces. Just scrub and rinse. A 50:50 vinegar/water mix will clean varnished wood and fiberglass, and raw vinegar cuts through grime and is great for wiping down work surfaces. The smell quickly dissipates. Close the heads and galley sink drain seacocks and pour baking powder down them to clean and deodorize. 


Heads Up

It doesn’t matter how scrupulous you are about keeping your heads compartment clean if you leave your intake hose and toilet bowl filled with seawater when you leave the boat. Microorganisms in the seawater will die and give off that nasty rotten-eggs hydrogen sulfide odor. If you first pump through plenty of salt water to make sure no waste is left trapped in the hose run, flushing a quart or two of freshwater through the toilet will take care of the toilet bowl and outlet hose, but what of the intake hose? “Headmistress” Peggy Hall suggests connecting the heads intake hose to the sink drain hose (if close enough) via T-fittings just upstream of the respective seacocks; before you leave the boat for more than a day or two, close both seacocks and then pump a sink full of freshwater through the toilet, which will rinse everything out. If you do this every time you leave the boat for more than a couple of days, you can kiss goodbye to stinky heads.


Rinse and Go

As turning blocks age their sheaves can become reluctant to spin freely. Sometimes this is due to wear, especially on plain-bearing blocks, but more often it’s due to buildups of dirt and salt clogging up the workings. These can harden to the extent that the usual perfunctory freshwater hose-down won’t shift them. Gently pour boiling water over the offending block. The heat should dissolve the salt build-up in no time. 


Why Sailors should Motor

It’s a point of pride among many sailors to use their auxiliary engines as little as possible, maybe just to get on and off the mooring. The problem here is that your diesel scarcely has a chance to warm up, and diesels don’t like such treatment. Fuel doesn’t combust properly and you end up with carbon buildups in the combustion chambers and exhaust system. A couple of times a season, take your boat out under power and run it hard—about 80% of maximum RPM—for an hour or so to clean your engine out. It will be grateful.


Poling Out a Headsail

Here’s a fuss-free way to pole your headsail out to windward. Set your whisker pole up with a downhaul, topping lift and afterguy. Roll up the headsail and lead the weather sheet through the jaws of the pole; do not clip the pole through the sail’s clew ring. Secure the pole into position by tensioning its three lines, then unroll the headsail and harden up on the sheet. If it is blowing hard, leave a couple of rolls in the genoa so that it sets nice and flat.



Too much leeway?

When you’re under sail, your boat will not be traveling a straight line through the water but will drift slightly to leeward. The amount of “leeway” a sailboat makes is dependent on many factors—wind strength, hull shape, and current— but usually is not much less than 5 degrees if you are sailing hard on the wind. If you aim 5 to 10 degrees upwind of your destination, you won’t go far wrong.


Knotty problem

When you have to make a docking line fast to a ring or bollard, a round turn and two half hitches is better than a bowline. Why? Because you can untie the round turn and two half hitches when the line is under load; try that with a bowline and you’ll soon be reaching for a knife. As a fringe benefit, the round turn also resists chafe.


Rode Markers

Plastic cable ties are available in many colors and can be used to mark your anchor chain and/or rope so you know how much rode you are paying out: one tie at 20 feet, two at 40 feet, or whatever interval works for you. By all means color-code the ties, but leave the tails long so you can feel them in the dark. Thin ties go through a windlass easily. 


Spring Time

Single-handed docking is greatly simplified if you use a midships spring line with a loop on its end. Make the spring line fast just abaft the boat’s pivot point; then as you slowly come alongside the dock, drop the loop over a dock cleat. If you leave the engine ticking over in forward gear, the boat will lie quietly alongside while you rig your other lines.


Hanging Around

Believe it or not, one of the most useful items you can keep on your cruiser is a metal coathanger. Cut and straightened, it can be used to unblock a hose, snake an electrical wire through inaccessible parts of a boat, hook lost objects out of a bilge, and catch a loose halyard that swings just out of reach. Oh, and it will keep your coat nicely crease-free!


String Theory

If you thought there already was too much “string” on your boat, think again. Keep a small bag full of odd lengths of 3/16in or 1/4in line—up to 6ft long—somewhere where you can find it in a hurry. You’ll be surprised how many uses you’ll find for short pieces of light line. There’s always something that needs to be lashed down or held up.


Hatch Love

Salt and grime can make your acrylic hatches and portlights look dull so make sure you wash them down with soap and water often. Don't use glass cleaners like Windex, as they contain abrasives. Faded Lexan (polycarbonate) hatches can be at least partially restored with a gentle car wax compound and a buffer, or a proprietary product like Aurora's Clear View. 


Prop Paint

You don't want barnacles or slime affecting your propeller's efficiency, but it's notoriously difficult to make antifouling paint stick to your prop. Here's how: rough up the metal with some 80 grit sandpaper, then apply a couple of coats of zinc chromate primer. Then brush on your choice of bottom paint. The primer will adhere to the metal, the paint will adhere to the primer, and the barnacles won't adhere to the paint.

0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users

Thailand Hotels | Bangkok Hotels | Phuket Hotels | Pattaya Hotels | Chiang Mai Hotels | Hua Hin Hotels